Ladle slag detection

The slag detector that never fails silently

SlagIQ listens to every pour, cuts out the plant noise and warns your crew as the vortex forms, before slag reaches the tundish. If a sensor or cable fails, you know that second. And every heat you pour makes it sharper at your caster.

The first prototype systems go to the first plants on the list. No cost, no commitment.

Scroll to watch it catch slag

The SlagIQ operator panel mid-pour: casting, armed, healthy

Armed

Watching every pour

Live vibration and the detection model on one panel at the deck. Grey means all is well.

Slag detected

An alarm your crew can trust

SlagIQ catches the vortex at the sensor before slag reaches the tundish. The panel takes over, the horn and lamp fire, and the relay trips for your gate logic.

Why crews stop trusting the slag alarm

Most slag detectors don't fail loudly. They drift. The screen still looks normal, and nobody finds out until there's slag in the tundish. Once the crew stops trusting the horn, every ladle closes on habit.

Close early and you leave steel in the ladle. Close late and you carry slag into the tundish. SlagIQ is built so your crew closes on the alarm, not on habit.

  1. The sensor works loose

    A single threaded stud backs off with heat and cable tugs. The signal fades and nothing on the screen changes.

    SlagIQ: four bolts and full flange contact keep it coupled. If coupling ever slips, SlagIQ flags it before it costs you a heat.

    How SlagIQ mounts
  2. Heat cooks it slowly

    Sensors that have been overheated drift for good. The alarms get a little worse every week.

    SlagIQ: the sensor watches its own temperature and signal, and asks to be swapped before it costs you a heat.

    How SlagIQ watches itself
  3. A damaged cable just gets noisy

    A half-broken analog cable doesn't fault. It picks up drive noise for months instead.

    SlagIQ: digital from sensor to cabinet. A damaged cable faults that second.

    Why SlagIQ is digital
  4. Every gate trim looks like slag

    Peak-to-peak logic fires on normal operator moves and crane noise, so crews learn to ignore the horn.

    SlagIQ: learns steel, slag, gate trims and ladle closes apart on your caster.

    How SlagIQ learns

The operator panel

One screen your crew reads from across the deck

The cabinet panel is built to ISA-101 high-performance HMI practice. It stays grey while everything is normal and uses colour only when somebody needs to act. Big states, big buttons, made for gloves.

Panel while casting: armed, healthy, live vibration and detection traces, outputs ready

Casting, armed, healthy. Live vibration and detection on the left, relay, horn and lamp ready on the right. Arming follows the pour, with a timer if your practice wants one.

SlagIQ control cabinet on a mill column, its panel showing CASTING ARMED
The SlagIQ cabinet mounts at the deck with its own panel, horn, alarm lamp and acknowledge button

Want a live walkthrough of the panel with your crew's questions?

Book a panel walkthrough

The smart sensor

A sensor that tells you when it's hurting

On the arm, at the nozzle

The sensor bolts to the shroud manipulator, right under the ladle nozzle where the vortex shows up first. It goes on in minutes with a high-temperature magnet base for a trial, then a weld plate for good.

One cable, digital the whole way

Power and data share one Cat6 line with a sealed M12 connector, run back along the boom in silicone-coated fibreglass fire sleeve. No analog signal to pick up drive noise. Damage the cable and the cabinet faults that second. Test it with an ordinary network tester.

Potted solid in 316 stainless

The electronics are cast solid inside the housing, so nothing can rattle, shift or take on water. Sealed to IP67 against cooling-water spray, splash and condensation. Bare stainless throws back the radiant heat that black housings soak up.

Four bolts, full contact

A wide square flange clamps flat to the plate with four bolts, so the vibration path stays tight heat after heat. No single stud to back off, no gasket to soften.

It knows what healthy looks like

SlagIQ learns what a good pour sounds like on your caster. The day the signal drifts from it, from heat, a loose mount or a tired cable, it flags the sensor and tells you to swap it. A green light on the sensor means healthy. Red means look at me.

Loading 3D view

Housing
316 stainless, potted
Sealing
IP67
Connection
M12 PoE, Cat6
Flange
124 mm, 4 bolts
Height
51 mm
Self-monitoring
Temperature, shock, signal
Heat protection
Reflective bare stainless
Status lights
Green healthy, red fault

It measures in full 3D and knows which way is up, so mounting angle never matters.

Want the drawings and mounting details for your manipulator?

Get the sensor spec sheet

Adaptive noise cancellation

Hears the vortex over the crane

On a casting deck the loudest thing in the signal is rarely the steel. Cranes, fans and ladle moves leak into every vibration sensor and bury the vortex that comes right before slag. An arc furnace in the same building can sing in exactly the band the vortex lives in.

SlagIQ measures the plant's own noise and subtracts it in real time, so the model hears the stream. Add a floor reference sensor and it cancels building vibration too.

  • No more alarms when the crane passes
  • Hears the vortex with the arc furnace running
  • Your spectrograms show the pour, not the building
Sensor signal, last 60 s of a pour
Illustration: with noise cancellation off, crane and furnace noise hide the vortex. With it on, the vortex before slag stands out. Vortex Crane EAF
Illustrative. Turn on noise cancellation to see what the model hears

Multi-modal detection

Slag has to get past vibration, video and heat

Four PoE ports on the cabinet take more SlagIQ sensors plus vision and IR cameras. One model weighs all of them on every pour, so a vortex that hides from one sense shows up in another.

If one input faults, the others keep watching and the panel says which one is down.

  • VibrationSmart sensor on the manipulator
  • VisionCamera on the stream or tundish
  • InfraredThermal camera on the pour
  • More smart sensorsA floor reference for building vibration

Human in the loop

SlagIQ Continuous Intelligence™

Most slag detectors are frozen the day they're commissioned. SlagIQ keeps learning your caster, your grades and your crew. It learns steel, slag, a gate trim and a ladle close apart, heat after heat, and your engineers decide when a better model goes live. The longer it runs, the fewer false alarms your crew sees and the fewer ladles close early.

  1. 1

    Operators answer at the end of the heat

    Slag this heat? Did the alarm come on time? Did you close on it? A few taps on the panel while it's fresh, about ten seconds. It can be skipped and never holds up the next ladle.

    Panel heat review after an alarm: alarm timing and closed-on-alarm questions, outcome Hit
  2. 2

    Engineers confirm in analytics

    Every answer lands in a review queue with the recording, spectrogram and alarm timing. Accept it in one click or correct it. Hits, misses and false alarms are counted for you.

    Analytics recording review: waveform, spectrogram and confirmed verdicts
  3. 3

    SlagIQ trains dozens of challengers while you cast

    Each confirmed heat becomes a training label. SlagIQ retrains and benchmarks dozens of model types on your plant's own heats and puts the best challenger up against the model you run today.

    Benchmarked on your plant's own heatsIllustrative
    Slag caughtFalse alarms
    Champion running
    Challenger 17
    Challenger 12
  4. 4

    Your engineer clicks Deploy

    Nothing changes on the deck until someone at your plant reviews the benchmark and approves it. Roll back to the previous model in one step.

    Challenger 17more slag caught, fewer false alarms
    Reviewed byprocess engineering
    Keep championDeploy
  5. 5

    Every decision on record

    A full audit trail shows which heats trained which model, who approved it and when it went live. When someone asks why the alarm fired, you have the answer.

    Analytics reviewed recordings with confirmed verdicts

Models trained at your plant are yours

Buy SlagIQ once. Every model the cabinet trains on your heats comes with it for as long as you run it. Perpetual licence, no mandatory subscription. When a more advanced model needs more GPU than the edge has, it can be trained on cloud compute, and you decide whether your data goes there.

See how Continuous Intelligence would learn on your heats

Reserve a Continuous Intelligence pilot

Integration

Drops into your caster, your network and your security rules

Runs on its own

It knows when you're casting from its own signal. No ladle-weight signal or PLC handshake needed to start.

More integrations as you need them

More protocols and systems are on the way. Tell us what your plant runs.

Talks to your systems

OPC UA, EtherNet/IP, Siemens S7, Modbus TCP and MQTT for your PLC and historian. Isolated discrete I/O for the horn, the lamp, your gate interlock and a heartbeat to the PLC.

Your IT team never opens a port

It runs fully offline with no inbound connections. Remote support runs over a VPN your plant switches on and off from the floor, and every session is logged.

Updates without a site visit

Containerised end to end. Updates arrive over that plant-controlled VPN or on signed media, and roll back in one step.

Cables that report their own health

Every cable runs in silicone-coated fibreglass fire sleeve, and system health watches each one. A damaged cable raises a fault on the panel instead of quietly adding noise.

Check SlagIQ against your PLC, historian and OT security setup

Talk to an engineer

Questions engineers ask

When can I get SlagIQ?

Prototype systems are being built now, and they go to the plants that join the list first. Joining costs nothing and commits you to nothing.

What does a prototype ask of my plant?

No outage: the magnet plate goes on between sequences with no welding. You provide power for a wall-mount cabinet near the deck and one cable run of up to 100 m. It runs in advisory mode beside your current practice, with no gate tie-in needed, and your crew answers a ten-second review at the end of each heat. From the first heat, those answers start training a model on your caster's own pours.

Can it close the gate?

Yes, if you want it to. Isolated outputs can drive your gate interlock directly, or SlagIQ can talk to your PLC over OPC UA, EtherNet/IP or S7. Your controls team decides the logic. On a power loss or fault, the fault and heartbeat contacts open, and SlagIQ never closes your gate by itself. The alarm, horn and lamp fire either way, and the alarm latches until someone acknowledges it.

What happens when the sensor fails?

The cabinet faults that second, the light on the sensor turns red, and the panel shows detection unavailable, so nobody casts on a blind system. SlagIQ also flags a sensor whose signal is drifting before it fails, and a swap is four bolts and one connector.

What about open pour, lancing or a shroud change?

SlagIQ tracks the state of the pour from its own signal. When the shroud is off or the ladle is being opened, it holds detection rather than arm on a signal it can't trust, and the panel says so. With a vision or IR camera on the cabinet, the camera keeps watching an open pour. If the manipulator swings away mid-heat, the panel shows detection paused until it is back on the nozzle.

Does it need a ladle-weight signal?

No. SlagIQ tells casting from not casting with its own signal and runs standalone.

How many heats before it's useful?

From the first heat. SlagIQ runs a baseline detector on day one, and every review your crew answers starts training a model on your own caster. You watch the benchmark climb in analytics, heat by heat.

Who owns the data and the models?

You do. Your heats and your models stay at your plant unless you turn on cloud training, and they are never pooled with anyone else's without your written consent.

Do I pay for model updates?

Models SlagIQ trains on the cabinet at your plant come with the system. Some more advanced models need more GPU compute than an edge computer has. Those can be trained on cloud compute over your plant-controlled VPN, and whether to use it is your call.

Does it need an internet connection?

No. It runs fully air-gapped with no inbound connections. The VPN for remote support stays off unless your plant turns it on.

Prototype program

Put SlagIQ on your caster first

We're building the first prototype systems now and choosing the plants that will run them. Prototypes run in advisory mode beside your current practice. No outage, no gate tie-in needed.

  • A walkthrough with the engineer who designed it
  • A place in line for a prototype system
  • Shape SlagIQ around your caster

What every prototype measures

  • Alarm lead time against the operator's close
  • False alarms per heat
  • Missed heats
  • Ladle residual and tundish slag against your current practice

You get the full report at the end of the trial.

No commitment and no sales sequence. An engineer reads every request.

What would you like?
Tell us about your caster (optional)

Next: a call with an engineer, a remote look at your deck, then install.